Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
How do you actually feel when it comes to A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't exactly rocket science, however it does call for strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old tub is conveniently easily accessible, the task can move quickly; if you need to open up a wall to eliminate the old bathtub and also position the new bath tub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. See to it you have qualified yourself for the job and fit attempting it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to consider using one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly assist you mount a brand-new bathtub in your shower room if you have actually currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your devices and material checklist must consist of the following:
Getting ready for the Installment
First of all, the sustaining framework provided with the bath ought to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to prevent strain on the bathtub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently be ready to be suited its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the limited access that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the remaining water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning during this process. Once the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Prior to going on to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Using the two wood boards under its feet, position the tub in the needed setting. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bath tub up until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost versatile tap connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water supply as well as inspect all joints and also brand-new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the bathtub must wait until the bathtub has been utilized at the very least once as this will certainly resolve it into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a link to the existing supply pipes.
If you need to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location in between the tap and also the sink. Secure the tap in position with the maker supplied backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap ports. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, causing the water to pass through the wall surface in between the bath and the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and also installations. They are marketed in tubes as well as cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before sealing, to permit the movement experienced when the tub is in usage. The sealer can break rather early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly offered on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader about How to Install a Bathtub, I figured sharing that excerpt was a great idea. Be sure to take the time to distribute this page if you appreciated it. Thanks for your time. Don't hesitate to come visit our website back soon.
Excellence in emergency plumbing services. Report this page